Cooper Bussmann 5073E-T Manual do Utilizador Página 2
- Página / 106
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
2 www.cooperbussmann.com/wirelessresources
Cooper Bussmann 5073E-T Managed Ethernet Switch User Manual
Rev Version 1.1
Interference Issues
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference
in a commercial or industrial installation. This equipment generates, uses, and can radiate radio frequency energy,
and may cause harmful interference to radio communications if it is not installed and used in accordance with the
instructions.
UL Listed Models
When operating at elevated temperature extremes, the surface may exceed +75°C. For user safety, the 5073E-T
should be installed in a restricted access location. The openings on the enclosure are for air convection. Protect the
equipment from overheating. Do not cover the openings.
UL Notice
This equipment shall be powered using an external listed power supply with LPS outputs or a Class 2 Power
Supply. The 5073E-T must be properly grounded for surge protection before use.
Hazardous Location Notices
This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D; ambient temperature –40˚C to +50˚C
or non-hazardous locations only.
WARNING: EXPLOSION HAZARD
Do not disconnect equipment unless power has been removed or the area is known to be non-hazardous.
WARNING: EXPLOSION HAZARD
Substitution of any components may impair suitability for Class I, Division 2.
WARNING: EXPLOSION HAZARD
The area must be known to be non-hazardous before servicing or replacing the unit and before installing the unit.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to
Part15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and may cause
harmful interference to radio communications if it is not installed and used in accordance with the instructions.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception (which can be determined by turning the equipment off
and on) try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a different circuit from that to which the receiver is connected.
• Consult the dealer or an experienced radio or TV technician for assistance.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause radio interference, in which case you
may be required to take adequate measures.
Important Notice
Cooper Bussmann/ELPRO Technologies reserves the right to modify the equipment, its specification, or this manual
without prior notice in the interest of improving performance, reliability, or servicing. At the time of publication all
data is correct for the operation of the equipment at the referenced voltage and/or temperature. Performance data
indicates typical values related to the particular product.
- Cooper Bussmann 1
- User Manual 1
- Release Notice 3
- Follow Instructions 3
- Proper Use 3
- CONTENTS 4
- 5Rev Version 1.1 5
- ChapTEr 1 - INTrODUCTION 6
- 1.3 Order Information 7
- 1.4 Hardware Features 7
- 1.5 Software Features 8
- 1.6 Package Contents 9
- 2.1 Front Panel 10
- 2.2 Top View 11
- 2.3 LED Indicators 11
- 3.1 Installation Steps 13
- 3.2 DIN Rail Mounting 13
- 3.3 Wall Mount Plate Mounting 14
- 3.4 Wiring the Power Inputs 15
- 3.6 Cabling 16
- 17Rev Version 1.1 17
- 4.1 Pro-Ring2se Application 19
- 5.2 Pin Assignment 21
- 5.4 CLI Management 23
- 6.2 System Login 24
- 6.3 Web Page Overview 25
- 6.4 System Menu 25
- CPU Load Average 26
- 6.4.2 Time - SNTP 27
- 29Rev Version 1.1 29
- 6.4.3 Account - Admin 30
- 6.4.4 IP Addressing – IPV4 30
- 6.4.5 Syslog 31
- 6.4.6 SNMP 32
- SNMP Trap Configuration 33
- 35Rev Version 1.1 35
- 37Rev Version 1.1 37
- 6.4.7 System Alert 38
- System Alert Event 39
- Digital Input/Digital Output 40
- 41Rev Version 1.1 41
- 6.4.8 DHCP Server 42
- DHCP Server Client Table 43
- DHCP Server IP Binding 43
- 6.5 Configure Menu 44
- Port Status 45
- Port Statistics 45
- Port Alert 46
- 6.5.2 Rate Control 47
- Storm Control 48
- 6.5.3 Aggregation 49
- 6.5.4 Spanning Tree 50
- RSTP Settings 51
- RSTP Information 52
- 53Rev Version 1.1 53
- 6.5.6 Multicast Support 54
- IGMP Snooping 55
- Static Filtering 55
- 6.5.7 LLDP 56
- 6.5.8 Filtering Data Base 57
- 6.5.9 VLAN 58
- 59Rev Version 1.1 59
- 61Rev Version 1.1 61
- VLAN Switch Status 62
- 6.5.10 QoS 63
- Port Priority 64
- COS Mapping to Queue 64
- 6.5.11 Port Mirroring 65
- 6.6 Security Menu 66
- Static Table 67
- 6.6.2 802.1X/Radius 68
- 802.1X/Radius Port Setting 69
- 802.1X/Radius Port Status 69
- 6.6.3 MAC Filtering 70
- 6.7 Maintenance 71
- 6.7.2 Restart Device 72
- 6.7.3 Factory Defaults 72
- 6.7.4 Firmware Upgrade 72
- 6.7.5 Export/Import 73
- 6.7.6 Diagnostics 75
- 6.8 Troubleshooting 76
- 77Rev Version 1.1 77
- 10 /100BASE-TX Pinouts 78
- RJ-45 Pin Assignments 78
- 10/100Base-TX Cable Schematic 78
- 10/100/1000Base-TX Pinouts 79
- 802.1x Commands 80
- Admin Password Commands 81
- Backup and Restore Commands 81
- CLI Commands 82
- DHCP Server Commands 82
- Factory Default Command 83
- Fault Alarm Commands 83
- IGMP Commands 84
- IP Security Commands 85
- IP Setting Commands 85
- LLDP Commands 86
- Loading Average Commands 86
- Logout Command 86
- MAC Address Table Commands 86
- MAC Blacklist Commands 87
- Ping Command 88
- Port Control Commands 88
- Port Monitoring Commands 89
- Port Security Commands 89
- Port Statistics Commands 90
- Port Status Command 90
- Pro-Ring2se Commands 90
- Rate Limit Commands 91
- RSTP Commands 92
- Save Configuration Command 93
- SFP Monitor Command 93
- SNMP Commands 93
- SNTP Commands 94
- Switch Setting Commands 94
- System Event Log Command 95
- System Reboot Command 95
- System Warning Commands 95
- Trunk Commands 97
- Upgrade Firmware Command 97
- VLAN Commands 98
- 99Rev Version 1.1 99
- Rev Version 1.1 100
- 101Rev Version 1.1 101
- 103Rev Version 1.1 103
- Term Definition 104
- ©2013 Cooper Bussmann 106
- Rev Version 1.1106 106
Manuais e produtos relacionados com Redes Cooper Bussmann 5073E-T
(4 páginas)Canon FS40 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Kamerarekorder Canon FS40.
Wir stellen 2 PDF-Handbücher Canon FS40 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung, Bedienerhandbuch
Comentários a estes Manuais