Cooper Bussmann 5073E-T Manual do Utilizador Página 67
- Página / 106
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
www.cooperbussmann.com/wirelessresources
Cooper Bussmann 5073E-T Managed Ethernet Switch User Manual
67Rev Version 1.1
IP Security Mode Enable or disable IP security. When security is enabled, the fields on this page
become active.
Enable Web
Management
When this checkbox is selected, any device whose IP address matches one of the
10IPaddresses in the Security IP1–P10 table (see the next section) will be given
permission to access this switch via HTTP service.
Enable Telnet
Management
When this checkbox is selected, any device whose IP address matches one of the
10IP addresses in the Security IP1–IP10 table (see the next section) will be given
permission to access this switch via Telnet service.
Enable SNMP
Management
When this checkbox is selected, any device whose IPaddress matches one of the
10IPaddresses in the Security IP1–IP10 table (see the next section) will be given
permission to access this switch via SNMP service.
Apply Click to apply the settings.
Static Table
The system allows you to assign up to ten IP addresses for access security. When IP Security Mode is enabled on
the IP Source Guard Configuration page, only these ten IP addresses will be able to access and manage the switch
through the HTTP/Telnet/SNMP service.
To set up the IP address table, click the Static Table tab on the IP Source Guard Configuration page. (To display
this page, choose Security-->IP Source Guard-->Configuration.)
NOTE Remember to choose Maintenance-->Save Configuration, and then click “Save” to save the new
configuration. Otherwise, the new configuration will be lost when the switch powers off. See “6.7.1 Save
Configuration.”
Figure 72 IP Source Guard - Static Table
Security IP 1–10 Enter the IP addresses that will be allowed to access and manage the switch through
the HTTP/Telnet service.
Apply Click to apply the settings.
- Cooper Bussmann 1
- User Manual 1
- Release Notice 3
- Follow Instructions 3
- Proper Use 3
- CONTENTS 4
- 5Rev Version 1.1 5
- ChapTEr 1 - INTrODUCTION 6
- 1.3 Order Information 7
- 1.4 Hardware Features 7
- 1.5 Software Features 8
- 1.6 Package Contents 9
- 2.1 Front Panel 10
- 2.2 Top View 11
- 2.3 LED Indicators 11
- 3.1 Installation Steps 13
- 3.2 DIN Rail Mounting 13
- 3.3 Wall Mount Plate Mounting 14
- 3.4 Wiring the Power Inputs 15
- 3.6 Cabling 16
- 17Rev Version 1.1 17
- 4.1 Pro-Ring2se Application 19
- 5.2 Pin Assignment 21
- 5.4 CLI Management 23
- 6.2 System Login 24
- 6.3 Web Page Overview 25
- 6.4 System Menu 25
- CPU Load Average 26
- 6.4.2 Time - SNTP 27
- 29Rev Version 1.1 29
- 6.4.3 Account - Admin 30
- 6.4.4 IP Addressing – IPV4 30
- 6.4.5 Syslog 31
- 6.4.6 SNMP 32
- SNMP Trap Configuration 33
- 35Rev Version 1.1 35
- 37Rev Version 1.1 37
- 6.4.7 System Alert 38
- System Alert Event 39
- Digital Input/Digital Output 40
- 41Rev Version 1.1 41
- 6.4.8 DHCP Server 42
- DHCP Server Client Table 43
- DHCP Server IP Binding 43
- 6.5 Configure Menu 44
- Port Status 45
- Port Statistics 45
- Port Alert 46
- 6.5.2 Rate Control 47
- Storm Control 48
- 6.5.3 Aggregation 49
- 6.5.4 Spanning Tree 50
- RSTP Settings 51
- RSTP Information 52
- 53Rev Version 1.1 53
- 6.5.6 Multicast Support 54
- IGMP Snooping 55
- Static Filtering 55
- 6.5.7 LLDP 56
- 6.5.8 Filtering Data Base 57
- 6.5.9 VLAN 58
- 59Rev Version 1.1 59
- 61Rev Version 1.1 61
- VLAN Switch Status 62
- 6.5.10 QoS 63
- Port Priority 64
- COS Mapping to Queue 64
- 6.5.11 Port Mirroring 65
- 6.6 Security Menu 66
- Static Table 67
- 6.6.2 802.1X/Radius 68
- 802.1X/Radius Port Setting 69
- 802.1X/Radius Port Status 69
- 6.6.3 MAC Filtering 70
- 6.7 Maintenance 71
- 6.7.2 Restart Device 72
- 6.7.3 Factory Defaults 72
- 6.7.4 Firmware Upgrade 72
- 6.7.5 Export/Import 73
- 6.7.6 Diagnostics 75
- 6.8 Troubleshooting 76
- 77Rev Version 1.1 77
- 10 /100BASE-TX Pinouts 78
- RJ-45 Pin Assignments 78
- 10/100Base-TX Cable Schematic 78
- 10/100/1000Base-TX Pinouts 79
- 802.1x Commands 80
- Admin Password Commands 81
- Backup and Restore Commands 81
- CLI Commands 82
- DHCP Server Commands 82
- Factory Default Command 83
- Fault Alarm Commands 83
- IGMP Commands 84
- IP Security Commands 85
- IP Setting Commands 85
- LLDP Commands 86
- Loading Average Commands 86
- Logout Command 86
- MAC Address Table Commands 86
- MAC Blacklist Commands 87
- Ping Command 88
- Port Control Commands 88
- Port Monitoring Commands 89
- Port Security Commands 89
- Port Statistics Commands 90
- Port Status Command 90
- Pro-Ring2se Commands 90
- Rate Limit Commands 91
- RSTP Commands 92
- Save Configuration Command 93
- SFP Monitor Command 93
- SNMP Commands 93
- SNTP Commands 94
- Switch Setting Commands 94
- System Event Log Command 95
- System Reboot Command 95
- System Warning Commands 95
- Trunk Commands 97
- Upgrade Firmware Command 97
- VLAN Commands 98
- 99Rev Version 1.1 99
- Rev Version 1.1 100
- 101Rev Version 1.1 101
- 103Rev Version 1.1 103
- Term Definition 104
- ©2013 Cooper Bussmann 106
- Rev Version 1.1106 106
Manuais e produtos relacionados com Redes Cooper Bussmann 5073E-T
(4 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais